[Prelude to the Storage Bin // Part 1] Sisimay G3

 Hello, today's article will be a rewritten tutorial of the Sisimay G3.

Stats:

- 20cm

- 15.8 g

The materials you will need are as follows:

- 1* Pilot G3

- 1* Pilot Juice Up

- 1* Uniball Signo DX

- 1* Uniball Lakubo

- 1* Frixion Colors

- 1* Jimnock/Hyperjell/Jimnie

- 2* Papermate Profile / Dong-a Anyball

- Electrical Tape

The steps to construct the mod are as follows:

Remove the tip, inktube, and backplug of the G3. Do not clean the front.

                                                

Remove the plastic piece from your Frixion Colors cap.

Cut one of your Anyball/Profile grips so that you have 7 sections remaining (rings 5-11)

Cut your Signo DX grip on the 5th dimple.

Place your Signo DX tip into the Frixion Colors cap followed by your Jimnock/Jimnie/Hyperjell

Slide your cut DX grip over the G3, stopping where the end of the G3 grip is. 

The tipstack is Lakubo backplug > Juice Up tip.

Screw the tip on and fill the gap in with electrical tape.

Slide your cut 7 sections of Anyball onto the cap, and slide the 

remaining whole Anyball over the front of the G3. You're finished now, congrats.

Due to the construction of this G3, it doesn't take very long to make while at the same time offering a wide range of color customization options. I would say this G3 spins most similarly to Itezy-3 with the benefit of not being horribly unbalanced. Personally, I am not that big of a fan of G3 mods that are above 15 grams, especially ones with a dense feeling like this, so this mod, unfortunately, isn't for me. However, if heavier G3 mods are what you like, then I would highly recommend this mod. 

Original Tutorial links can be found here.

- Sisimay's Blog
- Penmoddingarchives

BT MX Tutorial

Hello, here is a quick tutorial for my BT MX. This has definitely been done before, but this is just the way I do it.

Materials:

    1x Stalogy Pen (BP or MP it doesn't matter)

    1x Bic Roundstic

    1x Pentel RSVP (Cap and Grip)

    1x Pentel HGG/HGR (Grip and Tip)

Steps:

    1. Take your Stalogy, disassemble it, and cut off this much from the clicker side. (2 cm ish depending on how long u wanna make your bt mx)

    2. Take your Bic Roundstic, remove the ink tube, and cut off this much. (3.5 cm not counting the ink tube holder)

    3. Place your HGG/HGR tip onto the front of the Bic Roundstic. If you are using HGG, the tip should screw onto the front of the Bic without any problems. If you are using HGR you will need to use tape to hold the tip to the front of the Bic. (If you don't want to use tape you could experiment with a G3 rubber to hold the tip down)

    4. Prepare your RSVP cap like usual.

    5. Assemble all the parts. The Bic portion will go onto the side with the threads and the cap will go on the cut side of the BT. (You may need a small portion of tape.)

    6. Finished!

    Notes: Honestly, if you don't like spinning MX, don't make this mod. You'll hate yourself for cutting up a BT and making a mod that spins like MX. On the bright side, if you think MX is cool and you wanna spice it up a bit, this is a great way to do that, especially if you like rubber barrels. Another good thing about this mod is that you can make an extended stalogy with the bt internals, so in my opinion, deciding to make this mod results in a win-win situation. Lastly, this same exact concept can be applied to the Kacogreen barrels, so if you want to make a KGMX, go for it :)